Item Specification
Eachine Wizard  X220S

Wheelbase: 220mm
Frame arm: 4mm carbon fiber
Weigh: 356g (without battery and camera mount)
Take off weigh: 561g
Package weigh: 1728g

3K carbon fiber frame kit, 4mm thickness and 15mm width frame arms, the width is 10mm less than Eachine Wizard X220.

Frame kit with camera angle scale and 30° camera mount for Runcam 3 for for gopro session. 

Anti-vibration sponges to protect the racer frome crashing.

Eachine  MN2206 2300KV motor

KV: 2300
Max thrust: 1100G
Length: 35MM
NO.OF cell: 3-5S
Diameter: 28MM
Framework: 12N14P
Shaft: 3MM
Propeller: 5 inch
Weight: 28g

Eachine 30A BLHELI_S  4 in 1 ESC
Con. current: 30A
peak- current (10S): 35A
Input  voltage: 2-5S
BEC: 5V output
Programming: YES
Firmware: blheli_s
Weight: 28g
Size: 36*36MM

Eachine 1179 800TVL CCD camera 
Color: purple

Sensor: CCD

Resolution(horizontal center): 800TVL

Shell size: 25mm*25mm

Weight: 11g

Resolution: PAL: 1980H×1080 (2MP)

Format: PAL

Video output: 1.0Vp-p/75Ω

Automatic gain control: 0.25/0.50/0.75/1.00 adjustable, up to 55dB.


Exposure mode: electron exposure

Electronic shutter: 1/50(1/60) - 1/100000 S

Gamma correction: 0.45/1.0

Synchronization method: internal synchronization

Lens: standard 2.8mm lens 

Working voltage: DC12V (Wide Voltage, measured that can be work in 5-13V)

Workig current: 70mA (low power consumption)

Workig temperature: -20℃--60℃

Humidity: 0%~98% 

Strong backlighting effect
5.8G 72CH 25MW 200mw 600MW

switchable transmitter

Video Format  : NTSC/PAL
Channel: 72CH
Operating Temperature : -10~85℃

Connector: RP-SMA Female

Antenna connector: RP-SMA Male

F4 V3 flight controller

Size: 36x36mm

Mount holes: 30.5x30.5mm

STM32 F405 MCU, Runs Betaflight 3.0.1 firmware, could run faster loop time. 

Using F4 MCU controls OSD over SPI bus in DMA mode.

OSD Configation has been included in Betaflight GUI. 

SBUS/PPM input (Pinheaders)

6PWM output (1-4Pinheaders and Sh1.0 Plug, 5-6 as Pinheaders)

With barometer

SPI Sensor MPU6000
Included 128Mbit Flash, please always use BEC for the fc-.

Supported by BETAFLIGHT and dRonin

Flysky FS-i6X 2.4GHz 10CH remote contro

Channel: 6-10 (Default 6)

Model Type: Fixed-Wing/Glider/Helicopter

RF Range: 2.408-2.475GHz

RF Power: < 20dBm

RF Channel: 135

band-width: 500KHz

2.4GHz System: AFHDS 2A / AFDHS

Modulation Type: GFSK

Stick Resolution 4096

Low Voltage Warning: < 4.2V

DSC port: PS/2 Port PPM

Chargeable: No

Antenna Length: 26mm (Dual Antenna)

Weight: 392g

Power: 6V DC 1.5AA*4

Display: STNTransflective Display, LCD 128x64 Lattice, VA 73x39mm, LCD with white backlight

Size: 174x89x190mm

On-line Update: Yes

Color: Black

Certificate: CE0678, fc-C ID: N4ZFLYSKYI6X

Flysky FS-A8S receiver

Channels: PPM 8CH
Model type: Multi-rotor

Frequency range: 2.408-2.475GHz

band- width: 500KHz

band- number: 135

RX Sensitivity: -92 dBm
2.4GHz system: AFHDS 2A

Modulation type: GFSK
DSC port: PPM
Transfer method: FHSS
Data output: 1.5mm*3 Pin  PPM

Antenna length: 26mm (Not including brass contacts)

Input power supply: 4.0-8.4V
Display method: LED
No ground interference ( Transmitting and receiving 1 m from the ground): >300m
Working current: 40mA
Each channel data: depend on the transmitter
Channel delay: <15mS
Size: 20*14*5.3mm

Weight: 1.2g

Certificate: CE0678, fc-CID: N45ZA8S00

1500mAH 4S 14.8V 75C battery

Capacity(mAh) : 1500

Cells (s): 4

Weight (g): 177

Length(mm): 80

Width(mm): 30

Height(mm): 33

Connector: XT60

Eachine 5051 3-blade propeller
Color: purple
Quantity: 10 Pairs
Mounting Hole: 5mm


(Package doesn't include Runcam 3, the Runcam 3 on the pictures for reference only.)

Package included:

1 x Eachine Wizard X220S frame kit

1 x Flysky FS-i6X remote control

1 x Flysky FS-A8S receiver

2 x 2206 2300KV motor CW 

2 x 2206 2300KV motor CCW

1 x Eachine 30A BLHELI_S  4 in 1 ESC

1 x Omnibus F4 V3 flight controller

1 x 800TVL camera 

1 x 5.8G 72CH 25MW 200mw 600MW switchable VTX

10 x Eachine 5051 3-blade propeller purple CW

10 x Eachine 5051 3-blade propeller purple CCW

1 x 1500mAH 4S 14.8V 75C battery
1 x 30° Camera Mount(For Runcam3/for for gopro session)

1 x B3 Pro charger

1 x Pagoda antenna

2 x Battery strap

2 x Wrench

More from this collection